Low-foam synthetic

TRIM C116 is a high-performance synthetic fluid for working cast iron and mild steels. State-of the-art technologies provide excellent cooling and chip settling, very low foam, good tramp oil rejection and machine cleanliness while leaving a protective film on the machine tool.

Provides excellent corrosion inhibition on ferrous alloys

Excellent biostability

Extremely low carry off for very low total operation costs

Very low foam and mist

Low chemical odour

Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts of your machine tools

Very good tramp oil rejection

Carbide Grinding Synthetic Fluid

TRIM C120 CG is formulated specifically for the carbide grinding industry. This synthetic product is intended for grinding carbide, but is equally good on ceramics, cermets, chill cast alloys and tool steels. TRIM C120 CG minimises cobalt leaching while still maintaining superior cutting and non-cutting characteristics.

Keeps super-abrasive wheels clean

Does not attack wheel bonding systems

Designed to carry grinding swarf to the filter but will release swarf in properly designed settling tanks

Will not be stripped out by conventional filtration systems

Is low foaming

Rejects tramp oil

Has superior sump life

Resists cobalt leaching for improved operator safety, stronger parts and cleaner machines

Very low carryoff for extremely low fluid operating costs

Easy recycling or disposal with conventional techniques and equipment

High-performance Synthetic
This product has Rolls Royce Approval CSS 130

TRIM C270 is a state-of-the-art synthetic coolant. C270 provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness, and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

Provides excellent corrosion inhibition on all common ferrous alloys

Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulphur-based EP additives

Extremely low carryoff for very low total operation costs

Very low foam and mist

Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips

Exceptional sump life and very good tramp oil rejection

Low initial charge odour which dissipates further after one or two days

Cutting and Grinding Fluid Concentrate

TRIM C272 is a synthetic coolant concentrate designed to operate at very high fluid pressures and volumes with little or no foam. TRIM C272 is ideally suited to situations where high coolant velocities or volumes are necessary to achieve maximum productivity. TRIM C272 is designed to have the superior cooling and chip settling characteristics of a premium synthetic product with the improved residues and mechanical lubricity of a semi-synthetic coolant. This product utilises an extremely effective and proprietary non-chlorine, non-sulphur extreme pressure additive for good tool life and improved surface finishes

Approved by the following aero engine OEMs – Rolls-Royce, GE and Safran Aero Engines, contact your Master Fluid Solutions representative for the relevant approval documentation

Very stable formula provides long operational life with consistent performance

Extremely low foam in mineral free water

Excellent tramp oil rejection

Water clear dilution aids filterability, reduces carryoff and facilitates getting the fluid to the point of cut

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Easy recycling or disposal with conventional techniques and equipment

High-performance low-foam synthetic

TRIM C274 is a high-performance synthetic fluid for working cast iron and steel alloys as well as corrosion resistant alloys such as inconel and titanium. TRIM C274 is ideally suited to situations where high coolant velocities or volumes are necessary to achieve maximum productivity. TRIM C274 is designed to have the superior cooling and chip settling characteristics of a premium synthetic product with the improved residues and mechanical lubricity of a semi-synthetic coolant. This product utilises an extremely effective and proprietary non-chlorine, non-sulphur extreme pressure additive for good tool life and improved surface finishes.

Very stable formula provides long operational life with consistent performance

Chlorine and sulphur free extreme pressure (EP) additives control built-up edge (BUE)

Excellent choice for nickel alloy, steel alloy and cast iron machining and grinding

Extremely low foam in mineral free water

Excellent tramp oil rejection

Water clear dilution aids filterability, reduces carryoff and facilitates getting the fluid to the point of cut

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Easy recycling or disposal with conventional techniques and equipment

Clean-running Synthetic

TRIM C276 is a synthetic coolant that meets the needs of the most modern and demanding manufacturers. C276 makes use of the latest synthetic coolant formulation and specially synthesized oil to produce a versatile product that is clean running, has great sump life, and is kind to both machines and operators. This product will perform well in centerless and cylindrical form grinding as well as on high-speed, single-point turning, and down-the-hole work on vertical and horizontal machining centers.

Very low foam and mist

Provides excellent corrosion inhibition on all common ferrous alloys

Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning

Excellent extreme pressure (EP) lubricity to do many form grinding, drilling and tapping operations

Extremely low carryoff for very low total operation costs

Exceptional sump life and very good tramp oil rejection

Low initial charge odour which dissipates further after one or two days

Minimizes the buildup of sticky residues

Cutting and Grinding Fluid Concentrate

TRIM C276WP is a synthetic coolant concentrate which operates at very high fluid pressures and volumes with little or no foam. TRIM C276WP is ideally suited to situations where high coolant velocities or volumes are necessary to achieve maximum productivity. TRIM C276WP has superior cooling, rust prevention and chip settling characteristics of a premium synthetic product combined with excellent compatibility with sensitive aluminium alloys.

Very stable formula provides long operational life with consistent performance

Extremely low foam in mineral free water

Excellent compatibility with sensitive aluminium alloys

Excellent tramp oil rejection

Water clear dilution aids filterability, reduces carryoff and facilitates getting the fluid to the point of cut

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Easy recycling or disposal with conventional techniques and equipment

Premium Synthetic Metalworking Fluid

TRIM C350 is a synthetic metalworking fluid optimised for the chemical, environmental, and machining requirements of the aerospace industry. C350 uses the best polymer technology to yield a very high performance, easy to use and maintain metal removal fluid. The combination of the proven synthetic polymer technology and nonchlorinated EP package produces very high levels of usable lubricity at the point-of-cut. C350's unique chemical formula allows superior, nonferrous corrosion prevention particularly on aerospace aluminium alloys.

Meets the most stringent nuclear and aerospace chemical content and machining requirements

Superior resistance to corrosion on both nonferrous and ferrous materials including aerospace aluminiums 7075, 2024, 3000, titanium, Inconel^®, brass, and high-strength alloy steels

Water-clear, low foaming, and misting, C350 is a joy to work with and manage

Provides superior results in a wide range of operations from general grinding to spar milling and turbine blade manufacture

Easily removed from parts for easy cleanup before assembly, painting, or plating operations

Very low carryoff and long sump life results in low operating cost

Cutting and Grinding Fluid Concentrate

TRIM C360 is a very low foam, high lubricity, high EP synthetic coolant that approaches the "down-the-hole" machining performance of premium soluble oils. TRIM C360 has been formulated especially for applications where maximum performance is required in machine tools which both machine and grind hard aerospace alloys in the same cycle. Due to its synthetic formula, TRIM C360 has exceptional tramp oil rejecting properties and is highly filterable through even the finest of filtration devices. This, coupled to a superb antimicrobial package, ensures prolonged sump life even in the harshest of machine shop environments.

A very versatile product that works well in a wide range of operations

Excellent extreme pressure performance without chlorine or sulphur additives

Keeps machines extremely clean whilst leaving a soft fluid film that protects metal surfaces

Water like working solution ensures low carry-off for low total operating cost

Keeps grinding wheels clean for higher feed rates, better surface integrity and faster stock removal

Highly filterable even through sub 10μm filters

Exceptional sump life

Exceptional tramp oil rejection

Coolant is easily removed with water or aqueous cleaners

Multi-metal Machining Emulsion

TRIM E715 is a high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM E715 makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Extremely hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE)

Extremely fine soluble oil emulsion reduces carryoff for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Suitable for machining aluminium alloys, steel alloys, nickel alloys, cast iron and yellow metals

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

Amine Free Machining & Grinding Emulsion

TRIM E720 is a high quality, universal soluble oil with a broad application range in machining and grinding of a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to heavy duty machining jobs on aluminium and stainless steel. The inhibitor package in TRIM E720 also makes it particularly suited to the machining of copper alloys without component staining or unsightly machine residues.

Very stable formula provides long operational life with consistent performance

Hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE)

Fine soluble oil emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Will run effectively for long periods without the need for costly additives

Boron-free, Multi-metal Machining Emulsion

TRIM E730 is a boron-free, high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM E730 makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Extremely hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE)

Extremely fine soluble oil emulsion reduces carryoff for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Suitable for machining aluminium alloys, steel alloys, nickel alloys, cast iron and yellow metals

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

Magnesium and multi-metal machining emulsion

TRIM E806 is a truly unique metalworking fluid emulsion concentrate with unparalleled metal compatibility and all round machining performance characteristics. The product is primarily designed for machining magnesium alloys used in the aerospace, automotive and general industry sectors. TRIM E806 does not tarnish the most sensitive magnesium alloys even after relatively long exposure times plus it is impervious to magnesium salt build-up in the sump - something which splits normal emulsions in a matter of days. Another problem with magnesium machining, hydrogen gas evolution, is virtually nil with TRIM E806. The product also has the lubricity and extreme pressure performance to machine other alloys commonly seen in the aerospace industry such as wrought aluminiums, stainless steels, inconel^® and titanium.

Safe for use on even the most sensitive magnesium alloys

Little or no hydrogen gas evolution when machining magnesium

Bio package extends useful life without the need for tank-side biocides or fungicides

Low foaming for todays demanding high-pressure, high-volume applications

Premium Emulsion

TRIM E850 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The optimised lubricity and extreme pressure package delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

Delivers exceptional lubricity

Very long sump life and low carry-off rates result in low operating cost

Low foam even in soft water areas

Hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials

Compatible with all materials excluding magnesium

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

High-lubricity, extreme pressure emulsion

TRIM E905 is a high quality, high lubricity universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. TRIM E905 has broad application in machining and grinding of a broad range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. The stable and predictable performance of TRIM E905 makes it a first choice for high quality, consistent parts manufacturing.

A very universal product that works well in a wide range of operations

Tried and tested extreme pressure (EP) additive controls built-up edge in tough operations

Extremely hard water tolerant

Very low foam even at high pressures

Extremely fine soluble oil emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Easily recycled or disposed of without special handling or equipment

Amine Free Machining & Grinding Emulsion

TRIM E909 is a high quality, universal soluble oil with a broad application range in machining and grinding of a wide range of materials. Very high levels of extreme pressure additives in this product make it particularly suitable for the heavy duty machining jobs on stainless steel and other difficult to machine alloys. The inhibitor package in TRIM E909 also makes it particularly suited to the machining of copper alloys without component staining or unsightly machine residues.

Very stable formula provides long operational life with consistent performance

Hard water tolerant

Traditional extreme pressure (EP) additives control built-up edge (BUE)

Fine soluble oil emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Will run effectively for long periods without the need for costly additives

Cutting and Grinding Fluid Concentrate

TRIM E923 is a proprietary blend of new vegetable-based technology and very high levels of chlorine free extreme pressure (EP) additives to yield an extreme performance, low management metal removal fluid. This premium emulsion product is robust enough to deliver unparalleled tool life in some of the most difficult metal cutting operations whilst still providing the excellent non-cutting characteristics normally associated with traditional, high quality emulsions from Master Fluid Solutions. The optimised lubricity and extreme pressure package matches heavy duty neat oils on difficult to machine materials such as inconel, titanium, stainless steel and high tensile strength steels.

Delivers exceptional lubricity and EP performance

Has the necessary performance to replace neat oils in certain applications

Very long sump life

Low foam even in soft water areas

Hard water tolerant

Compatible with all materials excluding magnesium

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

High Performance Machining Emulsion

TRIM E950 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is operator friendly because of its mild contact nature and low chemical initial-charge odour. TRIM E950 is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The unparalleled lubricity delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

Delivers unparalleled lubricity

Very long sump life and low carry-off rates result in low operating cost

Low foam even in soft water areas

Hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials

Fine emulsion ensures fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior tool life and corrosion prevention

Compatible with all materials excluding magnesium

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

neo-synthetic precision aerospace machining fluid

Experience ultimate versatility
HyperSol 888NXT's neo-synthetic technology masters the art of versatility. Providing exceptional performance on hard aerospace metals such as titanium and high-nickel alloys, stainless steels and Inconel^®, it also offers the superior lubricity necessary for machining soft, gummy aluminium alloys. Delivering low foam, low odour and a long running lifespan while meeting the strictest environmental regulations, HyperSol 888NXT is redefining excellence in the coolant industry.
See your production soar to new heights with revolutionary TRIM HyperSol™ 888NXT!

exceptional performance on hard aerospace metals

superior lubricity for machining softer aluminium alloys

trouble-free production

safest, environmentally-friendly ingredients

long-running lifespan delivers high customer value

less scrap, low foam and low odour

Low-foam Ferrous Semisynthetic

TRIM MicroSol 456 low-foam semisynthetic, microemulsion coolant is optimised for high-volume cast iron, ferrous, and some aluminium and nonferrous metalworking operations. MicroSol 456 prevents leaching of elemental iron and eliminates clinkering and oxidation of ferrous micro fines.

Delivering extended sump life, machine-friendly MicroSol 456 provides excellent, cost-effective cooling. Make a difference to your bottom line with MicroSol 456.

Low foaming for today's demanding high-pressure, high-volume applications

Also for machining some aluminium alloys and nonferrous metals

Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Requires no special disposal or recycling

Cutting and Grinding Fluid Concentrate

TRIM MicroSol 515 is a medium to high lubrication, semi-synthetic microemulsion coolant. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you would expect from a premium TRIM coolant. While it is particularly well suited for machining and grinding cast iron it does very well in mixed metal situations and is a proven performer when machining aluminium, inconel and titanium alloys.

Medium to high levels of lubrication without chlorinated or sulphurised EP additives

Compatible with aluminium, all steels, yellow metals and cast iron

Extremely hard water tolerant

Alternative to emulsion products for machining of high silica aluminium alloys

Fine soluble oil emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

No aggressive biocides

Easily recycled or disposed of without special handling or equipment

Contains no DEA, chlorine, sulphur, nitrites, formaldehyde releasers, or phenolic compounds

Premium Microemulsion

TRIM MicroSol 519 is a medium to high lubricity, semisynthetic, microemulsion coolant. The formula provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. Whilst it is particularly suited to machining and grinding cast iron and steel, it does very well in mixed metal situations and is a proven performer on aluminium alloys, stainless steels and titanium.

Formaldehyde releaser and boron free

Low foaming for modern high-pressure, high-volume applications

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Excellent alternative to high mineral oil soluble oils on high-silica aluminium alloys

Greatly extends useful life without the need for tank side biocides or fungicides

Optimised combination of cooling and lubricity for titanium machining applications

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Uses standard metalworking recycling and disposal techniques

High-lubricity Semisynthetic

TRIM MicroSol 530 is an environmentally-friendly semisynthetic, microemulsion coolant formulated especially for the machining of aluminium alloys. It utilises the newest technology to provide long-life and excellent protection of sensitive alloys. The outstanding lubrication properties of MicroSol 530 provide surface finish levels on aluminium components normally only seen with very high oil containing milky emulsions. Unlike those emulsions, MicroSol 530 is very clean running and keeps machine tools clear of unsightly residue build-up as well as reducing concentrate consumption.

Lubrication package gives excellent performance for aluminium machining

Excellent choice for aluminium alloy wheel machining applications

Optimised combination of cooling and lubricity for aluminium, titanium, steel, stainless steel, and Inconel^® machining applications

Protects and prevents corrosion on sensitive alloys, including aerospace and nuclear materials

Dramatically extends useful life without the need for tank-side biocides or fungicides

Low foaming for todays demanding high-pressure, high-volume applications

Excellent alternative to milky soluble oils on aluminium alloys

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps parts and machines very clean to reduce maintenance and coolant carry-off

Extended-life, Nonchlorinated Semisynthetic

TRIM MicroSol 585XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine-friendly characteristics you expect from a premium TRIM coolant. While it is particularly well suited for machining and grinding gray iron, it does very well in mixed metal situations. MicroSol 585XT has proven to be an exceptional machining fluid for titanium alloys.

Dramatically extends useful life without the need for tank side biocides or fungicides

Formaldehyde free

Low foaming for demanding high-pressure, high-volume applications

Compatible with a very wide range of material including steels, copper, and aluminium alloys, and many plastics and composites

Optimised combination of cooling and lubricity for titanium machining applications

Excellent alternative to high mineral oil soluble oils on high-silica aluminium alloys

Contains no nitrites, phenols and chlorinated or sulfurised EP additives

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Uses standard metalworking recycling and disposal techniques

Advanced Technology Aerospace Semisynthetic

TRIM MicroSol 590XT is an environmentally-friendly semisynthetic, microemulsion coolant formulated to pass aerospace approval test requirements. It utilises the newest technology to provide long life and excellent protection of sensitive alloys. MicroSol 590XT improves on the proven performance of previous generations with a robust stability package using the most environmentally-safe ingredients. The formula is a favorite of environmental advocates, safety professionals, and demanding production managers.

Meets the most stringent aerospace specifications

Protects and prevents corrosion on sensitive alloys, including aerospace and nuclear materials

Free of chlorine, formaldehyde releasers, phenols, boron, and secondary amines

Dramatically extends useful life without the need for tank-side biocides or fungicides

Low foaming for todays demanding high-pressure, high-volume applications

Optimised combination of cooling and lubricity for titanium, aluminium, steel, stainless steel, and Inconel^® machining applications

Excellent alternative to milky soluble oils on high-silica aluminium alloys

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps parts and machines very clean to reduce maintenance and production time

High-lubricity, Multi-metal Semisynthetic

TRIM MicroSol 651XT is a high-lubricity, low-foaming, multi-metal, semisynthetic microemulsion coolant. The formula offers the performance of a heavy-duty soluble oil with the cleanliness of a semisynthetic. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. An excellent alternative to soluble oils on high-silica aluminium alloys, MicroSol 651XT is compatible with a wide range of materials and operations.

High lubricity for extended tool life

Low foaming for today's high-pressure, high-volume coolant delivery systems

Excellent sump life without the use of tank side additives

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Hard water stable

Forms a tight microemulsion for low carryoff

Compatible with a wide range of materials and operations

Uses standard metalworking recycling and disposal techniques

High-lubricity, Low-foam Premium Semisynthetic

TRIM MicroSol 690XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. It does very well in mixed metal situations.

Dramatically extends useful life without the need for tank side biocides or fungicides

Boron and formaldehyde free

Low foaming for demanding high-pressure, high-volume applications

Compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper and aluminium alloys

Excellent alternative to high mineral oil soluble oils on high-silica aluminium alloys

Contains no nitrites, phenols, chlorinated or sulphurised EP additives

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Uses standard metalworking recycling and disposal techniques

Ester Based Superfinishing Oil

TRIM OE105 is an ester based neat grinding oil formulated for fine grinding and superfinishing. TRIM OE105 imparts excellent lubricity whilst keeping grinding wheels and stones extremely clean. This ensures fantastic surface finishes on hardened steel alloys, stainless steels and non-ferrous materials

Excellent extreme-pressure additive package for efficient metal removal

Very high lubricity

Great detergency

Fully saturated ester ensures unsurpassed oxidation stability

Ester based formulation ensures very low misting potential

Very high flash point for such a low viscosity product

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Ester Based Cutting and Grinding Oil

TRIM OE209 is a medium to heavy-duty neat cutting and grinding oil formulated using highly stable fully saturated esters. The product is certified as readily biodegradable. TRIM OE209 is designed for use in grinding and machining applications of hardened steel alloys, tool steels, stainless steels and carbide. TRIM OE209 has the lubricity and performance to maximise tool life in operations such as deep hole drilling and is particularly well suited for use in Sliding Head machines with high pressure chip breaker units.

Extremely high lubricity ensures fantastic tool life

Excellent detergency keeps grinding wheels clean

Does not leach cobalt from carbide tool alloys

Chlorine and sulphur free

Readily biodegradable

Saturated ester based formulation ensures very low foam and misting

Very High flash point

Unsurpassed oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Vegetable Ester Based Cutting Oil

TRIM OE310 NS is a heavy-duty neat cutting oil formulated using renewable vegetable esters and is used in very tough machining operations of hardened steel alloys, tool steels and stainless steels. TRIM OE310 NS is especially effective in deep hole drilling applications due to its low viscosity, lubricity and EP performance.

Excellent extreme-pressure additive package for efficient metal removal

Extremely high lubricity ensures fantastic tool life

Low viscosity ensures excellent chip removal in deep-hole drilling

Ester based formulation ensures very low misting potential

Very high flash point

Good oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Vegetable Ester Based Cutting Oil

TRIM OE315 NS is a heavy-duty neat cutting oil formulated using renewable vegetable esters. For use in very tough machining operations of hardened steel alloys, tool steels and stainless steels. TRIM OE315 NS is especially effective in deep hole drilling applications due to its reasonably low viscosity, lubricity and EP performance.

Excellent extreme-pressure additive package for efficient metal removal

Extremely high lubricity ensures fantastic tool life

Low viscosity ensures excellent chip removal in deep-hole drilling

Ester based formulation ensures very low misting potential

Very high flash point

Good oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Ester Based Neat Cutting Oil

TRIM OE322 NS is a heavy-duty neat cutting oil formulated using renewable vegetable esters. For use in very tough machining operations of hardened steel alloys, tool steels and stainless steels. TRIM OE322 NS is especially effective in modern, high performance lathes with high pressure chip-breaker units.

Excellent extreme-pressure additive package for efficient metal removal

Extremely high lubricity ensures fantastic tool life

Extremely low misting potential even with high pressure chip-breaker units

Very High flash point

Excellent oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Vegetable Ester Based Cutting Oil

TRIM OE330 NS is a very heavy-duty neat cutting oil formulated using renewable vegetable esters. TRIM OE330 NS is designed for use in very tough machining operations of hardened steel alloys, tool steels and corrosion resistant steel alloys. TRIM OE330 NS is especially effective in slow speed machining operations such as gear hobbing and broaching. The product can also be used to replace the dark, high odour neat oils used in Sunnen honing machines.

Excellent extreme-pressure additive package for efficient metal removal

Extremely high lubricity ensures fantastic tool life

Extremely low misting potential even with high pressure chip-breaker units

Very High flash point

Excellent oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

Vegetable Ester Based Cutting Oil

TRIM OE335 is a heavy-duty neat cutting oil formulated using renewable vegetable esters. The product is certified as readily biodegradable. TRIM OE335 is designed for use in very tough machining operations of hardened steel alloys, tool steels and stainless steels. TRIM OE335 has the lubricity and EP performance to maximise tool life in operations such as gear hobbing.

Extremely high lubricity ensures fantastic tool life

Readily biodegradable

Ester based formulation ensures very low misting potential

Very High flash point

Excellent oxidation stability

Compatible with copper containing alloys

Light colour and low odour for good operator acceptance

High Performance Tool Grinding Oil

TRIM OG108 is a very high specification grinding oil formulated for carbide and HSS tool grinding operations. The product utilises a very highly refined hydrocracked base oil which ensures very low levels of mist and high flash point. TRIM OG108 has been formulated to provide excellent wheel flushing properties together with good friction reduction and workpiece cooling.

Very highly refined base oil ensures low mist and high flash point

Good flushing properties keeps grinding wheels very clean

Excellent friction reducing properties ensures long wheel life

Excellent heat transferring properties

Excellent oxidation stability

Highly filterable in pre-coat filter systems

Low foaming

No reaction with cobalt

Kind to machine components and elastomers

Light colour and low odour for good operator acceptance

General Grinding Oil

TRIM OG210 is a very high specification, EP containing grinding oil formulated for grinding operations on all materials. The product utilises a very highly refined hydrocracked base oil which ensures very low levels of mist and a high flash point. TRIM OG210 has been formulated to provide excellent wheel flushing properties together with good friction reduction and workpiece cooling.

Very highly refined base oil ensures low mist and high flash point

Good flushing properties keeps grinding wheels very clean

Excellent lubricity and EP properties ensures long wheel life and good surface finish

Excellent heat transferring properties

Excellent oxidation stability

Highly filterable in pre-coat filter systems

Low foaming

No reaction with cobalt

Kind to machine components and elastomers

Light colour and low odour for good operator acceptance

Medium to Heavy Duty Neat Grinding Oil

TRIM OG225 is a medium to heavy-duty neat oil designed for use in grinding operations of hardened steel alloys, tool steels, stainless steels, inconels and titanium. A carefully selected extreme pressure/anti-wear package together with great detergency ensures TRIM OG225 provides very high stock removal rates in flute grinding without burning. It is also formulated to comply with aerospace regulations, i.e. no chlorine and no active sulphur additives. TRIM OG225 can also be used to machine all materials, including yellow metals, in high pressure applications where low oil mist is advantageous.

Excellent extreme-pressure/anti-wear additive package for efficient metal removal

Excellent filterability in precoat filter systems

Hydrocracked base oil ensures very low misting potential

Very High flash point

Low foaming

Excellent oxidation stability

Excellent compatibility with copper containing alloys

Light colour and low odour for good operator acceptance

Low Foaming Semisynthetic Fluid

TRIM SC415 is a lower foam, semisynthetic coolant specifically formulated for machining and grinding of cast iron and steel. This unique formulation ensures low levels of foam not generally seen with other semisynthetic products especially in soft water areas. This clean running formulation also prevents the loading of grinding wheels, ensuring good surface finishes and minimal burning.

A very versatile product that works well in a wide range of operations such as grinding, milling, turning, drilling, and tapping

Extremely good product for cast iron and steel machining and grinding

Extremely fine emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Extremely hard water tolerant

Easily recycled or disposed of without special handling or equipment

General Purpose, Ferrous Cutting and Grinding Fluid

TRIM SC417 is a cost effective, semisynthetic coolant specifically formulated for machining and grinding of cast iron and steel. This formulation achieves the highest levels of ferrous rust protection whilst also maintaining low levels of foam even in soft water areas. This clean running formulation also prevents the loading of grinding wheels, ensuring good surface finishes and minimal burning.

Extremely good product for cast iron and steel machining and grinding

A very versatile product that works well in a wide range of operations such as grinding, milling, turning, drilling and tapping

Extremely fine emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Extremely hard water tolerant

Easily recycled or disposed of without special handling or equipment

Low oil Semisynthetic

TRIM SC440 is a low foam, semisynthetic coolant specifically formulated for machining and grinding of cast iron and steel. This unique formulation ensures low levels of foam not generally seen with other semisynthetic products especially in soft water areas. This clean running formulation also prevents the loading of grinding wheels, ensuring good surface finishes and minimal burning.

Formaldehyde releaser and boron free

Provides superior corrosion inhibition on all ferrous metals

Fast wetting to get the fluid to the point of cut and keep grinding wheels clean

Low foaming for modern high-pressure, high-volume applications

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Greatly extends useful life without the need for tank side biocides or fungicides

Uses standard metalworking recycling and disposal techniques

Low foam Semisynthetic

TRIM SC440SW is a very low foam, semisynthetic coolant specifically formulated for machining and grinding of cast iron and steel in soft water. This unique formulation ensures low levels of foam not generally seen with other semisynthetic products. SC440SW's clean running formulation also prevents the loading of grinding wheels, ensuring good surface finishes and minimal burning.

No aggressive biocides

Low foaming even in soft water

Excellent rust protection to prevent clinkering of cast iron chips

Keeps the machine and work environment clean even when machining or grinding grey iron

Fine micro-emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and keep grinding wheels clean

Easily recycled or disposed of without special handling or equipment

Low-oil Semisynthetic

TRIM SC536 is a low oil, semisynthetic coolant that delivers significant performance improvements over previous generations of metalworking fluids. SC536 is a proprietary formula of specially synthesized oil and synthetic technologies blended to deliver unbeatable performance in a variety of machining and grinding operations. This innovative blend keeps machines clean and provides the longest sump life available.

Very low foam and mist

Provides excellent corrosion inhibition on all common ferrous alloys

Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning

Excellent extreme pressure (EP) lubricity to do many form grinding, drilling and tapping operations without the need for chlorine or sulfur-based EP additives

Extremely low carryoff for very low total operating costs

Exceptional sump life and very good tramp oil rejection

Very low initial odour level which usually disappears after on-to-two days

Minimizes the buildup of sticky residues

High Performance Semisynthetic Fluid

TRIM SC617 is a semisynthetic concentrate designed as a general purpose multi-metal coolant for general machining of ferrous and non-ferrous materials. TRIM SC617 uses a proven EP additive package to control built-up edge, improve tool life, and has the wetting and cooling characteristics for superior turning, milling and grinding results. It also has sufficient lubrication for most "down-the-hole" operations on machining centers.

A very versatile product that works well in a wide range of operations such as grinding, sawing, milling, turning, drilling, and tapping

Extremely good product for cast iron, steel and stainless steel machining and grinding

Low foam profile enables use in through tool machining applications

Very fine emulsion reduces carry-off for low total operating cost

Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention

Extremely hard water tolerant

Excellent tramp oil rejection together with highly biostable formulation ensures very long sump life

General-purpose Emulsion - Siloxane Free

TRIM™ SOL SF is a very high lubricity soluble oil which is suitable for machining and grinding a broad range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining of difficult materials such as stainless steel, inconel and titanium.

A very universal product that works well in a wide range of operations

Compatible with aluminium, all steels and yellow metals

Tried and tested extreme pressure (EP) additive controls built-up edge in tough operations

Hard water tolerant

Fine soluble oil emulsion reduces carry-off for low total operating cost

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Siloxane free

Easily recycled or disposed of without special handling or equipment

Nonchlorinated Tapping Fluid

TRIM TAP NC is a blend of synthetic and vegetable-based lubricants and additives with strong friction reducing properties. Use for metals with low machinability at full strength for flooding applications involving broaching, sawing, milling, tapping, threading, gear cutting, shaving, gundrilling, and reaming.

Especially for taps up to 25mm diameter

Promotes excellent finish

Ensures parts size control

Delivers exceptionally long tool life

Reduces rubbing of the tool flank

Compatible with most TRIM fluids

Use for added lubricity on extremely tough jobs

Paintable Antifoam/Defoamer

TRIM TC 239 is a paintable, plateable additive used to control foam in metalworking fluids and parts washing systems.

Paintable

Plateable

pH Adjuster

TRIM TC 256 is a mixture of compounds that are very effective in maintaining pH and building reserve alkalinity in metalworking fluid working solutions. Controlling pH within the design range of the product and maintaining an appropriate level of reserve alkalinity are key elements in extending sump life, controlling both liquid and vapor phase corrosion, and emulsion stability of soluble oils.

pH adjustment

Building reserve alkalinity

Extending sump life

Controlling both liquid and vapor phase corrosion

High-Performance-Ester-Fluid

WEDOLiT AE 1030 is a dewatering fluid based on the latest ester technology that uses surface-active substances to displace both water and emulsions from the metal surface quickly. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Not subject to the German solvent guideline VOC 31. BImSCHV or to the Swiss regulation concerning the incentive tax on volatile solvents (VOCV). Fulfils all requirements regarding ELV 2000/53/EG.

Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface

Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Excellent bath-life

Additive loss due to water contact: None

High-Performance-Ester-Fluid

WEDOLiT AE 4313 is a modern formulated, ester-based corrosion inhibitor for steel and other metals, which offers protection for short overseas transports. It can be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Suitable for short overseas transport

No negative labelling

Suitable for VCI-foils

Stable against acidic and alkaline contamination

Excellent material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

High-Protection-DW-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Ideal compatibility with VCI-foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Low

High-Protection-Fluid 170°C flash point (aromatic content ≤ 2%)

WEDOLiT AN 6999 is a modern formulated corrosion inhibitor for steel and other metals. It offers long-term corrosion protection (indoor storage and potentially outdoor storage) and can be applied by brushes or by means of rollers.

Ideal for overseas transport

Suitable for VCI-foils

Good protection for outdoor storage

Stable against acidic and alkaline contamination

Good material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Ideal for covered storage

Offers protection against atmospheric contamination, e.g. dissolved gases that cannot penetrate the protecting film (water vapour permeability)

High-Protection-DW-Fluid 120°C flash point

WEDOLiT AN-7114 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

WEDOLiT AN-7114 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Ideal compatibility with VCI-foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Low

Lanolin-Protection-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 7121 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or rolling. Homogenisation before usage is recommended.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Ideal for VCI-foils

Stable against acidic and alkaline contamination

Good material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Ideal for covered storage

Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)

High-Protection-DW-Fluid 130°C flash point
(aromatic content ≤2%)

WEDOLiT AN 7210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Suitable for overseas transport

Ideal compatibility with VCI-foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Low

Medium term RP 100°C flash point,

WEDOLiT AN 9921-100 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Can be used as a straightening oil or for light forming processes after the solvent has evaporated

Stable against acidic and alkaline contamination

Excellent bath life

Excellent material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

Dewatering-fluid 40°C flash point

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Dewatering-fluid 40°C flashpoint
(aromatic content ≥ 2%)

WEDOLiT AS 1211 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040212) under the name K 722.

Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

High-Protection-Wax-dispersion-Fluid 30°C flash point

WEDOLIiT AS 1723 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited period of outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface

Good protection for outdoor storage

It´s recommended to homogenise the product before use or after a longer storage period

Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

Universal RP 40°C flash point

WEDOiT AS 2111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2111-CM is a modern formulated corrosion inhibitor for steel and other metals, that offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Suitable for overseas transport

VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film

Stable against acidic and alkaline impurities

Good material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Water displacing with very good wetting behaviour

Additive loss due to water contact: Extremely low

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2241 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

Long term DW Fluid 40°C flash point

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Very low

High-Protection-Waxdispersion-Fluid 40°C flash point

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface

Good protection for outdoor storage

It´s recommended to homogenise the product before use or after a longer storage period

Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

Dewatering-fluid 60°C flash point

WEDOLiT AS 3040 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Special-Fluid 60°C flash point

WEDOLiT AS 4111 is a leading edge universally applicable, corrosion protection which offers a long-term protection for indoor storage. It has been especially developed for loosening rusted parts and can be applied by spraying, flooding or via an immersion bath.

Suitable for overseas tranpsort

Rust remover for humidity-related ignition problems in electrical systems

Loosens rusted screws, nuts, joints, hinges, switches and mechanisms

Cleans dirty tools and components and protects them from corrosion

Stable against acidic and alkaline impurities

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Water displacing with very good wetting behaviour

Additive loss due to water contact: Low

High-Protection-DW-Fluid 60°C flash point, thin film

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behaviour

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Very low

Dewatering-fluid 60°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 4143 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Protection-DW-Fluid 80°C flash point (aromatic content ≤ 2%)

WEDOLiT AS 6115 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV).

Suitable for short overseas transport

VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film

Stable against acidic and alkaline impurities

Good material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Water displacing with very good wetting behaviour

Additive loss due to water contact: Extremely low

Water-miscible, fully synthetic passivating agent

WEDOLIT AW 5700 is a water-soluble passivating agent for steel, which is also suitable for ultrasonic and hydro testing systems.

Almost free of foam and therefore suitable for high speed systems

Offers a short-term corrosion protection for indoor storage

Very good skin compatibility

Contains a special inhibit for copper and brass (for protection of fittings and testing equipment)

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. This mineral oil based product is not only suitable for steel, but also for non-ferrous metals. Utilising the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 60 - 80°C)

Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)

Easily removable with solvents or alkaline industrial cleaners

For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface

Very good compatibility with VCI foils

Outstanding material compatibility (even at higher concentration)

Assembly Fluid

WEDOLiT C 24-K is a water-soluble, fully synthetic fluid that facilitates the assembly of parts. The product is compatible with most non-ferrous metals and is also suitable for painted surfaces. However, the compatibility should be examined in preliminary tests. The product is also suitable for the expansion or reduction of aluminium tubes.

WEDOLiT C 24-K is approved by VW (Approval Number 29.4433).

The outstanding lubrication properties facilitate the assembly of components

Reduces friction and wear and thus contributes to a high tool life

Easily removable with organic solvents or alkaline industrial cleaners

High Performance Grinding Oil

WEDOLiT CN 2370-7 is a low viscous, high performance grinding oil based on the latest gas to liquid (GTL) technology. GTL-base-oils are free of aromatics, chlorine, zinc, nitrogen and heavy metals, to provide the best occupational safety for the worker. The product is suitable for the machining of HSS and carbides (especially with a high cobalt content). The product is also suitable for general cutting operations as well as for gear hobbing.

High performance product, which leads to an excellent surface finish and dimensional accuracy

Highly reduced oil mist formation, almost no loss of evaporation

Reduces friction and wear and thus contributes to a long tool life

Offers high cooling properties with a very good wetting behaviour

Very good flushing behaviour with an optimal transport of chips and swarf

Easily removable with organic solvents or alkaline industrial cleaners

High performance cutting oil

WEDOLiT CN 3650-13 is a mineral oil based cutting oil for the manufacturing (especially deep-hole drilling) of steel and aluminium alloys. The product contains a combination of EP- and AW-additives, which increase the cutting performance significantly.

High performance product, which leads to an excellent surface finish and dimensional accuracy

Highly reduced oil mist formation

Reduces friction and wear and thus contributes to a high tool life

Offers high cooling properties with a very good wetting behaviour

Very good flushing behaviour with an optimal transport of chips and swarf

Easily removable with organic solvents or alkaline industrial cleaners

High-performance cutting oil

WEDOLiT CN 5370-12 is a low viscous, non-water soluble high performance cutting oil based on the latest GTL-baseoil-technology, which was developed for thread cutting operations. The product is also suitable for general cutting operations of high alloyed steels, cast iron, aluminium and non-ferrous metals.

High performance product, which leads to an excellent surface finish and dimensional accuracy

Special additivation for thread cutting operations

Highly reduced oil mist formation, almost no loss of evaporation

Reduces friction and wear and thus contributes to a high tool life

Offers high cooling properties with a very good wetting behaviour

Very good flushing behaviour with an optimal transport of chips and swarf

Easily removable with organic solvents or alkaline industrial cleaners

High-performance cutting oil

WEDOLiT CN 5370-22 is a low viscous, non-water soluble, high performance cutting oil for thread cutting operations, which is based on the latest base-oil-technology. The product is also suitable for general cutting operations of high alloyed steels, cast iron, aluminium and non-ferrous metals.

High performance product, which leads to an excellent surface finish and dimensional accuracy

Special additivation for thread cutting operations

Highly reduced oil mist formation, almost no loss of evaporation

Reduces friction and wear and thus contributes to a long tool life

Offers high cooling properties with a very good wetting behaviour

Very good flushing behaviour with an optimal transport of chips and swarf

Easily removable with organic solvents or alkaline industrial cleaners

High performance oil

WEDOLiT CN 6850-26 is a medium viscous high-performance oil for machining steel, stainless steel, cast iron, aluminium and non-ferrous metals. By using this oil, various processes can be avoided such as separate production lines for machining different materials and the preliminary cleaning of non-ferrous metals. The product can be applied undiluted by spraying, flooding or means of rollers.

High performance product, which leads to an excellent surface finish and dimensional accuracy

Highly reduced oil mist formation, almost no loss of evaporation

Reduces friction and wear and thus contributes to a high tool life

Offers high cooling properties with a very good wetting behaviour

Very good flushing behaviour for an optimal transport of chips and swarf

Easily removable with organic solvents or alkaline industrial cleaners

A higher or lower viscosity can be created (equal additive content) by variation of the base oil

Minimum quantity lubricant

WEDOLiT CN 8250-2 is a volatilizing high-performance lubricant, designed for use in all types of low and minimum quantity lubrication systems for milling, sawing, thread cutting and cold forming applications of non-ferrous metals

High pressure absorption capacity as well as excellent wetting and lubricating effect

No gumming and sticking

Reduces build-up of material on steels with a low carbon content

The excellent cooling and lubricating properties lead to a significant increase in service life of tools and to high dimensional accuracy of workpieces

Ensures extremely economical use

Can be easily and safely removed by spray, immersion and ultrasonic cleaning with neutral or alkaline industrial cleaners or with organic solvents

High performance cutting and forming oil

WEDOLiT CN 8471-36 is an ester-based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

Stable load carrying capacity and a homogenous sliding behaviour

Very good wetting ability and film formation without adhesion

The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life

Leads to clean surfaces and contributes to achieve dimensional accuracy

Economical application

Very good oxidation stability

Easily removable with organic solvents or alkaline industrial cleaners

Minimum quantity lubricant

WEDOLiT CN 8570-25 is a liquid, odour-less, water insoluble high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

Stable load carrying capacity and a homogenous sliding behaviour

Very good wetting ability and film formation without adhesion

The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life

Leads to clean surfaces and contributes to achieve dimensional accuracy

Economical application

Almost no mist formation and residues

Very good oxidation stability

Easily removable with organic solvents or alkaline industrial cleaners

Water Soluble, High Performance Lubricant

WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

Offers high cooling- and flushing properties with a very good wetting behaviour

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a good skin compatibility

Recommended mixing ratio

Grinding:  from 4%

General cutting:  from 6%

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminium and their alloys.

Offers high cooling- and flushing properties with a very good wetting behaviour

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a good skin compatibility

Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

Water-miscible, conventional coolant

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series), titanium and non-ferrous metals*.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

Offers high cooling- and flushing properties with a very good wetting behaviour

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a very good skin compatibility

Water-miscible coolant

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series) and non-ferrous metals.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

Offers high cooling- and flushing properties with a very good wetting behaviour

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a very good skin compatibility

Water-miscible, ester-based coolant

WEDOLiT CW 8906 is suitable for grinding as well as light to heavy cutting operations of steel, stainless steel, aluminium and titanium.

Offers high cooling- and flushing properties with a very good wetting behaviour

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a very good skin compatibility

High performance expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil, ester-based

WEDOLiT EP 320 E is a highly viscous, high-performance, ester-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 540-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilising specific additives

Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 760 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilisation of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 760-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

High-performance forming oil

WEDOLiT FN 1170-225 is a medium viscous, chlorine containing forming oil for tube drawing and other cold forming operations of steel. The product offers also an excellent performance for precision cutting operations. The undiluted product is usually applied by spraying, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Soluble in chlorinated hydrocarbons

Fully synthetic forming oil

WEDOLiT FN 1430-115 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of non-ferrous metals. The undiluted product is usually applied by spraying, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

Fully synthetic forming oil

WEDOLiT FN 1430-220 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

Fully synthetic forming oil

WEDOLiT FN 1450-850 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

Semisynthetic forming oil

WEDOLiT FN 2451-150 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a long tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Ester-based forming oil

WEDOLiT FN 2451-180 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Fully synthetic forming oil

WEDOLiT FN 2451-850 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Fully synthetic forming oil

WEDOLiT FN 2551-1800 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Chlorinated stamping oil

WEDOLiT FN 4170-35 is a low viscous, water-insoluble chlorinated lubricant for heavy forming operations of steel and stainless steel. A combination of EP additives offers an outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Forming and stamping oil

WEDOLiT FN 4455-25 is a low viscous, water-insoluble lubricant for medium to heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Chlorine free stamping oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing or rolling.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a long tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Conventional Forming Oil

WEDOLiT FN 6870-170 is a medium viscous, water-insoluble lubricant for deep drawing and other cold forming processes of steel (e.g. for auto bodies). Additionally, the product is suitable as a spot lubricant for thread cutting or blind hole drilling. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

The product meets the requirements of the test procedure according to VDA 230-213.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High performance forming oil

WEDOLiT FN 6870-38 is a water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High performance forming oil

WEDOLiT FN 6870-440 is a high-performance product, which is based on highly refined mineral oils. The product is suitable for heavy forming and machining operations of steel, stainless steel and aluminium (e.g. thread cutting, stamping or deep drawing).

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behaviour, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation

Stable cold start behaviour, prevents stick-slip and chatter

Contributes to achieving dimensional accuracy

Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO₃) before further processing

Solvent base for aluminum stamping 70°C

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

Good spreading behaviour, which leads to a uniform wetting of the metal surface

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

Evaporating forming oil

WEDOLiT FS 6311 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals, which also performs excellently in thread rolling operations (aluminium). The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

Good spreading behaviour, which leads to a uniform wetting of the metal surface

Stable load carrying capacity and a homogenous sliding behaviour

Reduces friction and wear and thus contributes to a high tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

Calibration Oil

WEDOLiT FS 7400 is a non-water-miscible, evaporating calibration oil for light to medium calibration processes.

Can be applied by dipping or spraying

The residues left on the surfaces after calibration evaporate completely during annealing

Water-soluble, fully synthetic, good material compatibility

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

Offers very good high-pressure properties

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers very good skin compatibility

Recommended mixing ratio

Hydrofroming:  from 5 - 10%

Grinding:  from 3 - 6%

Stamping and Forming Medium

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels

Undiluted by brush or felt roller and can be easily washed off with water

Does not contain any insoluble pigments such as graphite or molybdenum disulfide

Water-miscible, fully synthetic coolant

WEDOLiT FW 7650 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Water-miscible, fully synthetic coolant for the whole tube welding line

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 4 - 6%

Water-miscible, fully synthetic coolant

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 4 - 6%

Wire drawing:  from 3 - 12%

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  3 -5%

Emulsion for the whole tube welding line

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 7%

Water-miscible high-performance-fluid

WEDOLiT K 102 is universally applicable for part cleaning and corrosion protection. The mineral oil containing product is not only suitable for steel, but also for non-ferrous metals. Based on the latest technology, it offers the possibility for a boron- and formaldehyde-free application.

The product forms a stable emulsion, regardless of the concentration

Due to the electrolyte and temperature stability, an application in a heated bath is possible (recommended temperature 60 - 80°C)

Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)

Easily removable with solvents or alkaline industrial cleaners

For corrosion protection it´s important that treated parts are completely dry before packaging

Depending on the concentration, a slightly noticeable film is formed on the metal surface

Very good compatibility with VCI foils

Outstanding material compatibility (even at higher concentration)

Basic-Fluid 200°C flash point
(aromatic content ≤ 2%)

WEDOLiT K 119 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for a short storage period and is suitable for light straightening processes. It can be applied by spraying, flooding or by means of rollers.

Approved by Porsche under PTL 6701-2001-06.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Suitable for VCI-foils

Stable against acidic and alkaline contamination

Good material compatibility

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Dewatering, short term RP 100°C

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be dewatered efficiently. It is mainly used as an immersion bath at room temperature.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface

Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Multi-purpose oil

WEDOLiT KS 3000 is a universally applicable corrosion protection/ rust remover which is also effective in case of moisture-related ignition problems of electrical systems. The product protects chrome parts, tools and machines from atmospheric influences, loosens rusted screws, joints, hinges, switches, cleans tools and parts and protects them from corrosion.

Very good creep behaviour (penetrates even very small cavities)

Loosens rusted joints

Stops squeaking

Provides temporary protections against corrosion

Very good lubrication properties even at low temperatures

To remove heavy staining or corrosion, it might be necessary to repeat the application

Water displacing with a very good wetting behaviour

Suitable for spot lubrication (e.g. for drilling operations)

Prelube

WEDOLiT N 22-4 is a medium-viscosity, non-water-soluble forming oil for deep-drawing sheet steel, for example, for the automotive industry. This includes sheet metal that is galvanized, or hot-dip galvanized on one or both sides, sheet metal coated with zinc metal, aluminized sheet metal, or sheets made of aluminum or aluminum alloys.

The product meets the requirements of the test procedure according to VDA 230-213, and has been approved by all VDA members.

Also acts as an anti-corrosion oil

Subsequent preservation of drawn parts is not necessary due to the good corrosion protection

Can be applied by spraying, flooding, brushing or with felt rollers

The oil film can be easily removed with organic solvents or water-soluble alkaline cleaners

Washing and forming oil

WEDOLiT N 22 NV is a thixotropic water insoluble washing oil for cleaning metal sheets and coils. The product is usually used in washing machines at ambient temperatures. Increasing the temperature to approx. 60 °C enhances the washing effect. The oil film that remains on the surface after the washing process offers sufficient forming properties for medium to heavy forming operations (for cold forming of uncoated and galvanized steel and for and aluminum).

Approved by Volkswagen (VW-Material-Nr. 29.4186) and by Mercedes Benz (Nr. 34/95-10576 VWT).

Compatible (according to tests and our experience) with all for the automotive industry typical adhesives and paints (KTL)

Acts as a corrosion protection agent. Therefore, a post-treatment of the drawn sheets is not necessary

An ageing stable film is formed after drawing

Can easily be removed with organic solvents or water soluble, mild industrial alkaline cleaning agents, even after long storage periods

A phosphating can easily be conducted after degreasing

Universal cutting oil

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing or thread forming steel, aluminium and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

Stable load carrying capacity and a homogenous sliding behaviour

Very good wetting ability and film formation without adhesion

Outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to long tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

Economical application

Easily removable with organic solvents or alkaline industrial cleaners

Economical Heavy-duty Spray Cleaner

Master STAGES™ CLEAN 2017 is an economical heavy-duty spray cleaner that removes heavy soils and oily residues from ferrous and magnesium parts. Often used in rebuild operations and for cleaning up cast iron, stamped or drawn steel parts, or removing heavy RP coatings.

Very economical way to remove heavy soils and light rust

Low foaming at ambient temperatures, and even lower when used above 49°C

Can be recycled using XYBEX^® equipment

Contains no solvents, borates, silicates, nitrites, or amines

Long bath life

Excellent compatibility with magnesium

Will prevent flash rusting and provide one-to-two days of in-process corrosion inhibition if not rinsed

Washing Compound for Ultrasonic and Immersion Washers

Master STAGES™ CLEAN 2020 is a concentrated, very high performance cleaner made for washing all metals including brass, copper alloy, and aluminium in ultrasonic or immersion washers. Its cleaning ability is extraordinary, which often leads to shorter cleaning cycles or elimination of cleaning steps. CLEAN 2020's oil rejecting properties mean longer bath life and economical operation.

Excellent cleaning in immersion and ultrasonic tanks

Long life because oils split rapidly to the surface of your cleaner tank where they can be skimmed off

An excellent choice where one product is used for multiple purposes; such as washing mixed batches of ferrous, aluminium, and copper alloy parts

Will provide extended in-process tarnish resistance on copper and copper alloy parts

Safe on aluminium, aluminium alloy, and magnesium

Will remove coolant residues as well as straight oils

Parts Washing Fluid with Corrosion Inhibitor

Master STAGES™ CLEAN 2029 "One Step" is a highly concentrated cleaner/corrosion inhibitor designed for spray washers and immersion tanks. This product will remove heavy soils and provide two-to-four weeks of indoor corrosion inhibition on steel and cast iron parts.

Formulated without silicates or other high pH additives, CLEAN 2029 "One Step" is compatible with ultrafiltration systems and bioremediation

An excellent choice for cabinet-style spray washers and can be used for washing steel, stainless, cast iron, titanium, and many aluminium alloys

Hard water tolerant, it provides long bath life

Environmental approvals are simplified because CLEAN 2029 "One Step" contains no nitrites, barium, phenols, or butyl cellosolve

This formula has very low V.O.C. content

Low foaming for use in high-pressure spray washers with temperatures above 60°C

Low Foam Spray Washing Compound

Master STAGES™ CLEAN 2115AL is an aluminium compatible, high performance, low foam synthetic washing compound for use in very high-pressure spray washers, de-burring, and water jet cutting. Advanced surfactant technology provides excellent foam control and tramp oil rejection.

Compatible with a wide range of materials including aluminium, cast iron, steels, zinc, plastics, and composites

Resists foaming even when contaminated with large quantities of soils or coolant. This makes CLEAN 2115AL an excellent choice where rapid buildup of coolant carryover creates a foam problem

Many CLEAN 2115AL applications are in the range of 3,000 to 10,000 PSI (200-700 Bar)

Provides short term corrosion inhibition on cast iron and ferrous alloys

Non-butyl Floor and Multi-purpose Cleaner

Master STAGES™ CLEAN F2™ is a super concentrate that does an outstanding job in floor cleaning and other multi-purpose uses. In addition to its primary job in automatic floor scrubbers, it is often used for general-purpose cleaning, mop bucket cleaning, and parts washing in room temperature wash tanks. The mild pH of this product means it is compatible with most waste treatment (including ultrafiltration) and it will not degrade TRIM metalworking fluids with which it may come into incidental contact.

With a mild pH and low conductivity, CLEAN F2 will not cause splitting of TRIM coolants

Formulated without silicates or other high pH additives, CLEAN F2 is compatible with ultrafiltration systems and bioremediation

CLEAN F2 has been proven nonirritating to skin at 20% concentration

An excellent choice for packaging in spray bottles up to 20%

Can be used for general cleaning tasks and to remove soils from parts and tools

Operators like CLEAN F2's mild, pleasant citrus scent

Environmental approvals are simplified because CLEAN F2 contains no nitrites, barium, phenols, or butyl cellusolve; this formula has very low V.O.C. content

An effective "mop bucket" cleaner in addition to use in floor scrubber machines

Will remove heavy soils from floors without lifting off floor paints, coatings, or leaving a slippery residue; suitable for concrete, painted, tile, or linoleum floors

Water Soluble Corrosion Inhibitor

Master STAGES™ NOCOR™ S2 is a synthetic, water soluble, ferrous corrosion inhibitor for short-term storage or shipment. Effective at concentrations from 3%—10% in water, it provides a very thin, water soluble protective film.

The transparent film left by NOCOR S2 is easily removed and will not interfere with additional machining, gauging, or assembly steps

Barium-free and contains very low levels of volatile organic compounds as applied

Mild Alkaline Detergent

Master STAGES™ RINSE 100 is a washing compound concentrate that does a great job of removing metalworking fluids and light oily films. This product will not stain ferrous or nonferrous materials and leaves an extremely thin film corrosion inhibitor, which does not interfere with gauging of parts. RINSE 100 is compatible with the TRIM family of cutting and grinding fluid concentrates.

Compatible with all aluminium, magnesium, copper alloys, steel and cast iron

An effective machine cleaner and also a great product for general cleaning of loose tools and parts

An excellent product for use in ultrasonic cleaner systems, as well as immersion washers

Provides up to one week or more of in-process corrosion inhibition on ferrous parts

Barium-free, Low Odor, Corrosion Inhibitor

Master STAGES™ RPO 6BF is a barium-free, nonstaining, water displacing, thin-film corrosion inhibitor or rust preventative which can be used on a variety of metals. RPO 6BF provides indoor corrosion inhibition, excellent protection for bearings and other precision parts, in-process parts in storage, as well as parts in transit.

Barium free

Light film for limited carryoff

Excellent corrosion inhibition, generally in excess of six months in dry storage

Nonstaining

Provides cleaning action

Water displacing to help prevent rust due to water trapped under the protective film

Oxidation resistant to resist tarnishing over long storage periods

Easily removed with detergent cleaners, such as Master STAGES™ CLEAN 2029 "One Step"

Humidity Cabinet Test: No rust at 650 hours (ASTM D1748)

Grime Fighter, Super Strength Industrial Cleaner

Master STAGES™ Task2™ is a grime fighting, industrial strength, non-butyl, water-based cleaning agent that does an outstanding job in the industrial, commercial, or office environment.

Use full strength or dilute up to 100:1

For the toughest industrial cleaning applications

Pratt Whitney Aerospace Approval PMC 1247-1

Contains no butyl, caustic, silicate, phosphate, nitrite, phenol, or borate

Very low V.O.C. content, and conductivity

Environmentally friendly, certified "Readily Biodegradable" by OECD Method 301D (EPA Guideline OPPTS 835.3110)

Will not harm TRIM metalworking fluids

Machine Tool Sump and System Cleaner
This Product has Rolls Royce Approval CSS203

Master STAGES™ Whamex™ is a safe, fast-acting concentrated formula that will save machine cleaning downtime while removing the oily residues, scums, and insoluble soap deposits that reduce coolant life. Whamex is made for cleaning out machine tool sumps and larger systems, coolant supply lines, and coolant recycling equipment. Whamex is compatible with most waste treatment (including ultrafiltration) and will not degrade TRIM metalworking fluids when used as directed.

A very specialized formula that draws many years of hands-on experience in machine clean outs

Quickly breaks down and lifts off insoluble scum deposits hidden in lines and difficult to reach areas — getting rid of these residues is one of the best ways to extend coolant life in your system

Very hard water tolerant allowing it to be effective in raw water or used coolant

Environmental approvals are simplified because Whamex contains no nitrites, phosphates, barium, phenols, or butyl cellusolve; this formula has very low V.O.C. content

When used as directed below, this product is compatible with TRIM brand semisynthetic, and soluble oil coolants, as well as most competitive coolants. Will remove heavy soils from machines without affecting paints, coatings, seals, hoses, or skirting, and it won't leave a slippery residue

Whamex will cause foaming in machines and systems running synthetic products. The use of non-foaming Whamex XT™ is recommended in such cases.

Short-term corrosion inhibitors prevent flash rusting of machine surfaces and ways

Low-foam Machine Tool Sump and System Cleaner

Master STAGES™ Whamex XT™ is a low foam, safe, fast-acting, concentrated formula that will save machine cleaning downtime while removing the oily residues, scums, and insoluble soap deposits that reduce coolant life. Whamex XT is made for cleaning out machine tool sumps and larger systems, coolant supply lines, and coolant recycling equipment. Whamex XT is compatible with most waste treatment (including ultrafiltration) and will not degrade TRIM metalworking fluids when used as directed.

A very specialized formula that draws on many years of hands-on experience in machine cleanouts

Quickly breaks down and lifts off insoluble scum deposits hidden in lines and difficult to reach areas — getting rid of these residues is one of the best ways to extend coolant life in your system

Very hard water tolerant allowing it to be effective in raw water or used coolant

Environmental approvals are simplified because Whamex XT contains no nitrites, phosphates, barium, phenols, or butyl cellosolve; this formula has very low V.O.C. content

When used as directed below, this product is compatible with TRIM brand synthetic, semisynthetic, and soluble oil coolants, as well as, most competitive coolants. Will remove heavy soils from machines without affecting paints, coatings, seals, hoses, or skirting, and it won't leave a slippery residue

Short-term corrosion inhibitors prevent flash rusting of machine surfaces and ways