Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

TRIM

TRIM™ C115

Synthetic

TRIM C115 is a high-performance, synthetic fluid for working cast iron and mild steels. State-of-the-art chemical technology provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness while leaving a protective film on the machine tool.

  • Does an excellent job in most glass, ceramic, and composite grinding applications
  • Excellent corrosion inhibition on most common ferrous and nonferrous alloys
  • Extremely low carryoff keeps operating costs down
  • Low foam and mist
  • Very low initial odor level which usually disappears after one-to-two days
  • Keeps your machines clean while leaving a soft, fluid film that protects bare metal parts
  • Exceptional sump life and very good tramp oil rejection

  • TRIM™ C270

    High-performance Synthetic

    TRIM C270 is a state-of-the-art synthetic coolant. C270 provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness, and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

  • C270 is compatible with a very wide range of materials including: cast iron, steels, and copper alloys, as well as plastics and composites
  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives
  • Extremely low carryoff for very low total operation costs
  • Very low foam and mist
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
  • Exceptional sump life and very good tramp oil rejection
  • A very low initial odor level which usually disappears after one-to-two days

  • TRIM™ C270CG

    High-performance Synthetic

    TRIM C270CG is a state-of-the-art synthetic coolant. C270CG provides excellent cooling and chip settling, good tramp oil rejection and machine cleanliness and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives
  • Extremely low carryoff for very low total operation costs
  • Very low foam and mist
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
  • Exceptional sump life and very good tramp oil rejection
  • A very low initial odor which usually disappears after one to two days

  • TRIM™ C276

    Clean-running Synthetic

    TRIM C276 is a synthetic coolant that meets the needs of the most modern and demanding manufacturers. C276 makes use of the latest synthetic coolant formulation and specially synthesized oil to produce a versatile product that is clean running, has great sump life, and is kind to both machines and operators. This product will perform well in centerless and cylindrical form grinding as well as on high-speed, single-point turning, and down-the-hole work on vertical and horizontal machining centers.

  • Very low foam and mist
  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning
  • Excellent extreme pressure (EP) lubricity to do many form grinding, drilling, and tapping operations
  • Extremely low carryoff for very low total operation costs
  • Exceptional sump life and very good tramp oil rejection
  • Low initial charge odor which dissipates further after one or two days
  • Minimizes the buildup of sticky residues

  • TRIM™ C290

    Economical Synthetic Fluid for Aluminum Machining

    TRIM C290 is a synthetic metalworking fluid optimized for the chemical, environmental, and machining requirements of general aluminum parts. C290 is a high performance, easy to use and maintain, metal removal fluid with very high levels of usable lubricity at the point-of-cut. C290's unique chemical formula allows great, nonferrous corrosion prevention on most aluminum alloys.

  • Great resistance to corrosion on nonferrous materials including aerospace aluminums 6061, 7075, 2024, 3000
  • Water-clear, low-foaming and -misting, C290 is a joy to work with and manage
  • Provides good results in a wide range of grinding and machining operations
  • Excellent tramp oil rejection
  • Easily removed from parts for easy cleanup before assembly, painting, or plating operations
  • PRTR compliant, no SARA 313 reportable chemistry. Product contains no chlorine, phenol, nitrites, copper, triazine, or silicone
  • Very low carryoff and long sump life results in low operating cost

  • TRIM™ C350

    Premium Synthetic Metalworking Fluid

    TRIM C350 is a synthetic metalworking fluid optimized for the chemical, environmental, and machining requirements of the North American aerospace industry. C350 uses the best of the new ester technology to yield a very high performance, easy to use and maintain metal removal fluid. The combination of the proven synthetic ester technology and nonchlorinated EP package produces very high levels of usable lubricity at the point-of-cut. C350's unique chemical formula allows superior, nonferrous corrosion prevention particularly on aerospace aluminum alloys.

  • Meets the most stringent nuclear and aerospace chemical content and machining requirements
  • Superior resistance to corrosion on both nonferrous and ferrous materials including aerospace aluminums 7075, 2024, 3000, titanium, Inconel®, brass, and high-strength alloy steels
  • Water-clear, low foaming, and misting, C350 is a joy to work with and manage
  • Provides superior results in a wide range of operations from general grinding to spar milling and turbine blade manufacture
  • Easily removed from parts for easy cleanup before assembly, painting, or plating operations
  • PRTR compliant, no SARA 313 reportable chemistry. Product contains no chlorine, phenol, nitrites, copper, triazine, or silicone
  • Very low carryoff and long sump life results in low operating cost

  • TRIM™ C385

    High-lubricity Honing Synthetic

    TRIM C385 is a state-of-the-art synthetic coolant which provides excellent cooling and chip removal, good tramp oil rejection and machine cleanliness. C385 meets the need of the modern job shop for a single premium synthetic coolant for honing and virtually all machining operations.

  • Very low foam and mist
  • Great for form grinding, honing, boring, rolling, etc
  • Exceptional sump life and very good tramp oil rejection
  • Extremely low carry-off for very low total operating costs
  • Very low initial odor which usually disappears after 1-2 days
  • Compatible with dirty or grey cast iron cutting, grinding, and honing
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts
  • The residual film is easily resoluble in the coolant working solution to facilitate easy machine cleaning and to minimize the buildup of sticky residues that can hold machine-destroying chips

  • TRIM™ DRIVE CF2P

    High-performance for Hard Disk Drives

    TRIM™ DRIVE CF2P is a specialized, chlorine-free, moderate-duty coolant formulated to meet the high-precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. It has very good wetting and lubricity giving excellent surface finishes. Its ease of wash-ability makes DRIVE CF2P an excellent choice for HDD components manufacturers. TRIM DRIVE CF2P will run in high-pressure situations with little to no foam.

  • In addition to aluminum alloy, it is also suitable for a wide range of materials including steels and stainless steels
  • Low foam even in high-pressure operations without the use of silicone antifoam
  • Good hydrodynamic lubrication to perform reaming and threading applications
  • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
  • Keep machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
  • Does not require special disposal and is easily recycled
  • Non-staining on aluminum alloys commonly used to produce HDD components
  • After machining, parts can be washed easily and completely in aqueous washing systems

  • TRIM™ DRIVE CF3

    High-performance Fluid for Hard Disk Drives

    TRIM DRIVE CF3 is a specialized, chlorine-free, heavy-duty coolant formulated to meet the high-precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. It has very good wetting and great lubricity resulting in excellent surface finishes and its ease of wash-ability makes DRIVE CF3 an excellent choice for HDD components manufacturers. TRIM DRIVE CF3 will run in high-pressure situations with little to no foam.

  • In addition to aluminum alloy, it is also suitable for a wide range of materials including steels and stainless steels
  • Low foam even in high-pressure operations without the use of silicone antifoam
  • Good hydrodynamic lubrication to perform reaming and threading applications
  • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
  • Keeps machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
  • Does not require special disposal and is easily recycled
  • Non-staining on aluminum alloys commonly used to produce HDD components
  • After machining, parts can be washed easily and completely in aqueous washing systems

  • TRIM™ DRIVE G2 161C

    High-lubricity, Low-foam Semisynthetic

    TRIM DRIVE G2 161C is a specialized, halogen-free, high lubricity semisynthetic coolant formulated to meet the high precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. DRIVE G2 161C has very good wetting and lubricity giving excellent surface finishes. Its ease of wash-ability make DRIVE G2 161C an excellent choice for HDD components manufacturers. DRIVE G2 161C will run in high-pressure situations with little to no foam.

  • Suitable for a wide range of materials including aluminum alloys, steels, and stainless steels
  • Non-staining on aluminum alloys commonly used to produce HDD components
  • Low foam even in high-pressure operations without the use of silicone antifoam
  • Good hydrodynamic lubrication to perform drilling, reaming, and threading applications
  • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
  • Keep machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
  • Does not require special disposal and is easily recycled
  • Parts machined with DRIVE G2 161C can be washed easily and completely in aqueous washing systems

  • TRIM™ E206KS

    Long-life Emulsion

    TRIM E206KS is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E206KS makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Has a very wide application range allowing its effective use on cutting and grinding
  • Extremely hard water tolerance
  • Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut
  • Provides good tool life and surface finishes
  • High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled
  • Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures
  • Coolant residue is easily removed with either water, working solution or aqueous cleaners
  • Good cleaning performance keeps machine tool very clean
  • Easy recycling or disposal with conventional techniques and equipment
  • Run effectively for long periods without the need for costly additives

  • TRIM™ E709

    Long-life Emulsion

    TRIM™ E709 is high-quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. The stable and predictable performance of E709 makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range, suitable for both grinding and machining
  • Fine particle size emulsion reduces carryoff and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, E709 has the right balance of cooling and lubrication to provide good tool life and surface finishes
  • Compatible with aluminum, steel alloys, cast iron, and yellow metals
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
  • Coolant is easily removed with water, working solution, or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Does not contain or test positive for phenol
  • Will run effectively for long periods without the need for costly additives

  • TRIM™ E709FF

    Long-life Emulsion

    TRIM E709FF is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E709FF makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Has a very wide application range allowing its effective use on cutting and grinding
  • Extremely hard water tolerance
  • Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut
  • Provides good tool life and surface finishes
  • High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled
  • Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures
  • Coolant residue is easily removed with either water, working solution or aqueous cleaners
  • Good cleaning performance keeps machine tool very clean
  • Easy recycling or disposal with conventional techniques and equipment
  • Run effectively for long periods without the need for costly additives

  • TRIM™ E711

    Copper Alloy Machining Fluid

    TRIM E711 is a high quality soluble oil designed primarily for the machining and grinding of yellow metals and copper alloys.

  • Rejects tramp oil to extend sump life
  • Will not stain or darken brass or other yellow metal alloys
  • Easy recycling or disposal with conventional techniques and equipment
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Very stable formula provides long operational life with consistent performance
  • Will not form the sticky, water insoluble residues commonly seen when machining yellow metals
  • Fine particle size emulsion reduces carryoff and facilitates getting the fluid to the point of cut
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
  • Compatible with all ferrous and nonferrous materials but is specifically designed for "free machining" yellow metals
  • Provides sufficient mechanical lubricity to run well in older "Swiss" style machines as well as in modern high speed CNC machines

  • TRIM™ E712

    Low Maintenance, General Purpose Emulsion

    TRIM™ E712 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protection film on the work piece and machine parts to prevent corrosion on metal surface including the machine tool. The stable and predictable performance of TRIM E712 makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range. Suitable for both grinding and machining
  • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, provides good tool life and surface finishes
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Will run effectively for long periods without the need for costly additives. Easily recyclable and/or dispose with conventional recycling and/or disposal techniques

  • TRIM™ E738

    Magnesium Machining Emulsion

    TRIM E738 is a soluble oil or chemical emulsion coolant concentrate designed for magnesium alloy machining. It provides excellent performance for high-temperature aerospace alloy and cast magnesium alloy. TRIM E738 consists of micro-molecular particles that provide advantages such as low mist levels, good cleaning and wetting performance. It provides mechanical lubrication, and is safe and very popular with operators.

  • Extremely hard water tolerable
  • High alkalinity reservation and release capability
  • Very tight emulsion particle structure that provides excellent wetting and cooling
  • Can reach cutting areas even in very high-speed cutting situations
  • Leaves a fluid residue to keep machine tool very clean
  • Prevents hydrogen and magnesium salts
  • Easy recycling or disposal with conventional techniques and equipment
  • Contains a highly effective extreme-pressure (EP) additive to control built-up edge (BUE)

  • TRIM™ E860

    Low-foam, High-lubricity Emulsion

    TRIM E860 is a high-quality, general purpose emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E860 makes it a first choice for precision and consistent parts manufacturing.

  • Very wide application range
  • Good hard water tolerance
  • Keeps machine tools clean
  • Works very well in general machining
  • Very stable formula provides good operational life with consistent performance
  • High tramp oil resistance for easy oil removal and longer coolant life
  • Easily recycled or disposed of using conventional techniques and equipment
  • Good balance of cooling and lubrication providing good tool life and surface finishes
  • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
  • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

  • TRIM™ E860KS

    Premium, General-purpose Emulsion

    TRIM E860KS is a high quality, general-purpose emulsion, which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protective film on the work piece and machine parts to prevent corrosion on metal surfaces including the machine tool. The stable and predictable performance of TRIM E860KS makes it a first choice for high quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range
  • Suitable for both grinding and machining
  • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, provides good tool life and surface finishes
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Will run effectively for long periods without the need for costly additives
  • Works very well in general machining where traditional soluble oil may not cool sufficiently

  • TRIM™ E9010BX

    High Performance Emulsion

    TRIM E9010BX is a soluble oil coolant concentrate designed as a general purpose multi-metal coolant for general machining of ferrous and nonferrous materials. It has the lubricity and "guts" necessary to do heavy-duty machining center work and still provide the wetting and cooling necessary to do high-speed turning and grinding operations.

  • Contains a proven and highly effective extreme-pressure (EP) additive to control built-up edge (BUE)
  • Has a very wide application range allowing its effective use on such diverse operations as production, surface and centerless grinding, heavy duty broaching, gear hobbing and replacing straight oil on some types of screw machines
  • Extremely stable fine particle size emulsion to reduce carryoff and to facilitate getting the fluid to the point of cut
  • Rejects tramp oil to help extend sump life and increase recycling options
  • Leaves a oily fluid, nongumming residue to prevent sticky ways, chucks, tool holders, and fixtures
  • Coolant residue is easily removed with either water, working solution, or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ E935

    Premium Universal Emulsion

    TRIM E935 is a premium universal emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E935 makes it a first choice for precision and consistent parts manufacturing.

  • Very wide application range
  • Good hard water tolerance
  • Keeps machine tools clean
  • Works very well in general machining
  • Very stable formula provides good operational life with consistent performance
  • High tramp oil resistance for easy oil removal and longer coolant life
  • Easily recycled or disposed of using conventional techniques and equipment
  • Good balance of cooling and lubrication providing good tool life and surface finishes
  • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
  • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

  • TRIM™ E950

    High Performance Machining Emulsion

    TRIM E950 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is operator friendly because of its mild contact nature and low chemical initial-charge odour. TRIM E950 is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The unparalleled lubricity delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

  • Delivers unparalleled lubricity
  • Very long sump life and low carry-off rates result in low operating cost
  • Low foam even in soft water areas
  • Hard water tolerant
  • Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials
  • Fine emulsion ensures fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior tool life and corrosion prevention
  • Compatible with all materials excluding magnesium
  • Easily recycled or disposed of without special handling or equipment
  • Will run effectively for long periods without the need for costly additives

  • TRIM™ GRIND WCS

    Boron Free - Carbide Grinding Synthetic

    TRIM GRIND WCS minimizes cobalt leaching in the grinding of tungsten carbide (WC) and other high cobalt materials. Minimal cobalt leaching means increased piece part integrity, while improving "G RATIOS" and reducing grinding forces. GRIND WCS is specifically designed for the carbide grinding industry; it will also perform very well in grinding ceramics, cermets, and tool steels.

  • PRTR compliant
  • Keeps super-abrasive wheels clean while not attacking super-abrasive wheel bonding systems
  • Carries grinding swarf to the filter, but will release swarf in properly designed settling tanks
  • Is not stripped out by conventional filtration systems
  • Operators like GRIND WCS’s clear working solution for superior visibility while grinding
  • Exceptional sump life and good tramp oil rejection for easy skimming
  • Resists oxidation and varnishing
  • Resists cobalt leaching for improved operator safety, stronger parts, and cleaner machines
  • Very low carryoff equals low fluid makeup costs
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ HM

    Cutting and Grinding Fluid Concentrate

    TRIM HM is a synthetic cutting and grinding fluid concentrate. It was developed to facilitate the manufacture of cutting tools from High-Speed Steels (HSS), Chill Cast Alloys, and other high-strength, high-hardness tool materials. TRIM HM is intended for situations where high-heat removal and low working concentrations are critical. TRIM HM is particularly well suited for surface grinding and similar operations requiring maximum heat transfer. It is often used effectively in double disc grinding, belt grinding, and abrasive cutoff operations on ferrous materials.

  • Is water clear with a fluorescent green tint to facilitate the operators' view of the work piece
  • Even at very low concentrations it has extended sump life
  • Settles chips and swarf rapidly and lends itself to very high flux rates in positive media filtration
  • Low mist and odor
  • Very low foam even at very high pressures and flow rates
  • Low foaming wetting agents to keep the wheel clean and prevent wheel loading
  • Will not attack super abrasives or their wheel bonding systems
  • Coolant residue is easily cleaned up with either water or working solution
  • Rejects tramp oil for easy skimming and recycling
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ MicroSol™ 456

    Low-foam Ferrous Semisynthetic

    TRIM MicroSol 456 low-foam semisynthetic, microemulsion coolant is optimised for high-volume cast iron, ferrous, and some aluminium and nonferrous metalworking operations. MicroSol 456 prevents leaching of elemental iron and eliminates clinkering and oxidation of ferrous micro fines.

    Delivering extended sump life, machine-friendly MicroSol 456 provides excellent, cost-effective cooling. Make a difference to your bottom line with MicroSol 456.

  • Low foaming for today's demanding high-pressure, high-volume applications
  • Also for machining some aluminium alloys and nonferrous metals
  • Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Requires no special disposal or recycling

  • TRIM™ MicroSol™ 585XT

    Extended-life, Nonchlorinated Semisynthetic

    TRIM MicroSol 585XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine-friendly characteristics you expect from a premium TRIM coolant. While it is particularly well suited for machining and grinding gray iron, it does very well in mixed metal situations. MicroSol 585XT has proven to be an exceptional machining fluid for titanium alloys.

  • Dramatically extends useful life without the need for tank-side biocides or fungicides
  • Low foaming for todays demanding high-pressure, high-volume applications
  • Compatible with a very wide range of material including cast iron, steels, copper, titanium, and aluminum alloys, and many plastics and composites
  • Optimized combination of cooling and lubricity for titanium machining applications
  • Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems
  • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
  • Contains no nitrites, triazines, phenols, and chlorinated or sulfurized EP additives
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Uses standard metalworking recycling and disposal techniques

  • TRIM™ MicroSol™ 590XT

    Advanced Technology Aerospace Semisynthetic

    TRIM MicroSol 590XT is an environmentally-friendly semisynthetic, microemulsion coolant formulated to pass aerospace approval test requirements. It utilizes the newest technology to provide long life and excellent protection of sensitive alloys. MicroSol 590XT improves on the proven performance of previous generations with a robust stability package using the most environmentally-safe ingredients. The formula is a favorite of environmental advocates, safety professionals, and demanding production managers.

  • Meets the most stringent aerospace specifications and has received many aerospace approvals
  • Protects and prevents corrosion on sensitive alloys, including aerospace and nuclear materials
  • Free of chlorine, triazine, formaldehyde releasers, phenols, boron,and secondary amines
  • Dramatically extends useful life without the need for tank-side biocides or fungicides
  • Low foaming for todays demanding high-pressure, high-volume applications
  • Optimized combination of cooling and lubricity for titanium, aluminum, steel, stainless steel, and Inconel® machining applications
  • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals
  • Keeps parts and machines very clean to reduce maintenance and production time

  • TRIM™ MicroSol™ 687NXT

    Premium High-lube PRTR Microemulsion

    TRIM MicroSol 687NXT is a translucent, premium high-lube, PRTR compliant microemulsion. The product is low foaming in soft water but is also stable in hard water. The product is designed to machine difficult to machine metals, such as stainless steel and Inconel. It is also good for most aluminum alloys including aerospace grade.

  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Excellent compatibility with a very wide range of material including stainless steel, nickel alloys, titanium, and aluminum alloys
  • Greatly extends useful life without the need for tank side biocides or fungicides
  • Low foaming for modern high-pressure, high-volume applications
  • Uses standard metalworking recycling and disposal techniques
  • Does not contain any chemical listed under Japan PRTR regulation
  • Provides superior corrosion inhibition on all ferrous metals

  • TRIM™ MicroSol™ 690XT

    High-lubricity, Low-foam Premium Semisynthetic

    TRIM MicroSol 690XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys.

  • Dramatically extends useful life without the need for tank-side biocides or fungicides
  • Boron and halogen free
  • Low foaming for todays demanding high-pressure, high-volume applications
  • Compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys
  • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
  • Contains no nitrites, triazines, phenols, chlorinated, or sulfurized EP additives
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Uses standard metalworking recycling and disposal techniques

  • TRIM™ MicroSol™ 692XT

    Premium, High-lubricity, Low-foam Microemulsion

    TRIM MicroSol 692XT is a high-lubricity, semisynthetic, microemulsion coolant. This formula delivers extended sump life, greater bio stability, and better foam control versus previous generation semisynthetic Microemulsions. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys. Improved tramp oil rejection keeps your production running smoothly. Increase your profitability and production with TRIM MicroSol 692XT!

  • Improved lubricity for longer tool life
  • Dramatically extends useful life without the need for tank-side biocides or fungicides
  • Halogen free
  • Low foaming for todays demanding high-pressure, high-volume applications
  • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Requires no special disposal or recycling techniques

  • TRIM™ MQL™ 100

    Minimum Quantity Lubrication Fluid

    TRIM MQL™ 100 is a high performance, vegetable-ester based micro lubrication fluid. It is fully compatible with all “micro lube” and micro mist systems. MQL 100 contains a blend of environmental and operator friendly materials that provide very high levels of EP and boundary lubrication to control built up edge (BUE) and sliding friction. MQL 100 outperforms the competition in sawing, drilling, tapping, and milling, to name but a few. In situations where it is impractical to use a micro lubrication applicator, MQL 100 may be manually applied to the tool or work piece.

  • Very low mist
  • Environmentally friendly, renewable resource based
  • Low consumption, out-performing the more expensive products
  • Easily water washable – does not produce hard to remove residues
  • Promotes superior finish and tool life and is compatible with all materials
  • Has been extensively tested and proven in all major brands of micro lube applicators
  • Very high levels of lubricity with minimum quantities of material at the point of cut for high material removal

  • TRIM™ OGM100HF

    High Flash Point Gear Grinding Oil

    TRIM OGM100HF is a high-efficiency grinding oil composed of high-quality mineral oil and various high-quality oil additives. This product has good permeability and lubricity, and can be used in the grinding process of materials (especially gear grinding) like cast iron, alloy steel, stainless steel, etc. It is also suitable for various profile grinding, internal and external grinding, cutting, centerless grinding, and other grinding processes.

  • Does not contain phosphorus or heavy metals, which protects the environment and reduces pollution
  • Light color, low odor
  • Good material compatibility
  • Safe and non-irritating to the skin
  • Produces good surface finishes
  • Provides high-strength lubricity in various medium-to-heavy-duty machining operations
  • Meets the cutting requirements of various machining operations: such as, automatic lathes, special machines, CNC lathes, and machining centers.

  • TRIM™ OM 210

    High-performance, Cutting and Grinding Oil

    TRIM OM 210 is a low-odor, light-colored oil designed for operations where low viscosity and high lubricity are required. In addition to general machining, OM 210 is particularly effective in deep-hole drilling and creepfeed grinding where its ability to flow into the cutting zone and "wet" the surfaces increases tool life and reduces heat.

  • Light color and low odor
  • High flash point
  • Minimal carry over loss
  • Excellent chips flushing and low foam
  • Oxidation inhibited for longer life
  • Excellent tool life properties

  • TRIM™ OM 303

    Nonchlorinated Cutting and Lubricating Oil

    TRIM OM 303 is a highly formulated straight oil designed for use in conventional and Swiss style screw machines, high-speed turning centers, and high-performance, multi-station machines, such as Hydromats. OM 303 is safe for use on aluminum alloy and steel alloy parts, as well as cast iron, copper, brass, and bronze. This product is excellent for high-pressure applications such as thread rolling and thread-form tapping. OM 303 has proven itself in difficult operations on stainless and bearing steels. OM 303 provides lubrication properties similar to ISO 32 general-purpose lube oils.

  • Very light colored and clean running
  • Low foaming and low misting for use in aggressive operations
  • Oxidation inhibited for longer life, and an excellent choice where both ferrous and aluminum or copper alloy parts are being machined aggressively
  • Far easier to wash off parts than many oils of similar or even lower performance
  • Has replaced dark, active sulfur/chlorine straight oils in several large operations while providing superior results in tool life
  • An outstanding product in thread rolling, thread form tapping, and in Swiss screw machines with solid bushings
  • Contains no active sulfur; therefore, does not stain parts

  • TRIM™ OM 360

    Straight Cutting Oil

    TRIM OM 360 is a high quality mineral oil containing an effective synthetical ester additive. It is designed for cutting and grinding a wide range of materials, and especially for steel broaching. This product can also be used for tapping, gear milling, or reaming. It is also suitable for aluminum alloy machining and steel heat treatment.

  • Excellent EP lubricating performance, good built up edge control (B.U.E.), provides super surface finish
  • Provides outstanding lubricating and cooling necessary for deep hole machining
  • Low mist and volatilization, keep working environment clean

  • TRIM™ OM350C

    Heavy-duty Cutting Oil

    TRIM OM350C is a heavy duty, mineral oil based cutting oil formulated with high performance synthetic ester-based additives. It can be used for a variety of metal cutting and grinding processing, especially suitable for steel broaching. This product is also suitable for tapping, milling, and reaming processes. Also suitable for multi metal applications such as copper alloy, aluminum alloy, and heat-treated steel.

  • Excellent extreme pressure lubrication, inhibiting BUE generated, providing an excellent surface finish
  • Provides excellent lubrication and cooling for machining deep holes
  • Low oil mist, low volatility, maintains a clean working environment

  • TRIM™ SC310

    Microemulsion Semisynthetic

    TRIM™ SC310 is a high-oil, semichemical coolant. This product combines the cooling, rust inhibition, and wetting of a premium synthetic with the mechanical lubricity and machine "friendliness" of a soluble oil. SC310 is well-suited for general, high-speed machining and grinding of all materials.

  • Compatible with a very wide range of material including: cast iron, steels, copper, and many plastics and composites
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals and eliminates “hot chip” and clinkering problems often seen when machining cast iron
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Has exceptional sump life and very low makeup for extremely low total operating cost
  • Low odor and mist makes for an operator-friendly product
  • Extremely effective EP additive package
  • Contains no nitrites, heavy metals, phenolic compounds
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ SC410

    Chlorine-free Semisynthetic Coolant

    5 drum minimum batch order size. Pricing and delivery available upon request.



    TRIM SC410 is a chlorine-free, semisynthetic coolant using vegetable-derived and ester lubricants. It is very clean running in moderate-duty machining and grinding of both ferrous and nonferrous materials. In addition to its broad range of machining qualities, it has been specially optimized for machining "gray iron"castings and for surface and cylindrical grinding of ferrous materials.

  • Based on our exclusive ester lubricant technology, contains no mineral (petroleum) oil
  • Low foaming in most operations
  • Compatible with a very wide range of materials including ferrous, nonferrous, and nonmetallic material
  • Will provide superior sump life and corrosion inhibition for long periods of time without adds
  • Prevents chip "clinkering" and "hot" chip hoppers when machining cast iron
  • Will keep the machine and work environment clean even when machining or grinding gray iron
  • Contains no chlorine or sulfur-based additives
  • Contains no nitrites, sulfonates, Alkylphenol Ethoxylates, or phenols and is not SARA 313 reportable
  • Very low carryoff and long sump life, delivering low operating costs
  • Hard water tolerant up to 30 grains

  • TRIM™ SC538

    High-performance Semisynthetic Fluid

    TRIM SC538 a high-performance semisynthetic coolant. Provides superior aluminum machinability, boundary lubrication, and produces a very high quality surface finish. Can also be utilized for ferrous and non-ferrous metal materials, stainless steel, and aerospace alloy materials. SC538 has good lubricity and friction reducing qualities in high-speed cutting and grinding applications.

  • Provides superior aluminum machinability
  • Very high quality surface finish
  • Has exceptional sump life and very low makeup for extremely low total operating cost
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Low odor and mist makes for an operator friendly product
  • Easy recycling and disposal with conventional techniques and equipment

  • TRIM™ SC639

    General Purpose Semisynthetic

    TRIM SC639 is a general purpose semisynthetic cutting and grinding fluid concentrate which provides an excellent balance between cooling and lubricity. SC639 has very good corrosion protection for both ferrous and non-ferrous metal, and can be used for a wide range of high-speed turning and grinding operations. SC639 leaves a thin layer of water soluble oil residue that provides extra protection to the machine tools parts while keeping the machine clean.

  • Provides excellent lubricity for various machining applications
  • Provides excellent corrosion and rust inhibition on ferrous and nonferrous alloys, preventing clinkering problems of cast iron chips in machining
  • Keeps machines very clean and leaves a soft fluid film for easy cleaning and less machine maintenance
  • Long sump life and low coolant consumption that reduce the cost for user
  • Low odor and mist that provides a good working environment
  • Good hard water tolerance up to 40 grain
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ SC9030

    High-lubricity Semisynthetic

    TRIM SC9030 is a high-oil semisynthetic coolant. This product provides the cooling, rust inhibition, and wetting of a premium synthetic with the mechanical lubricity and machine "friendliness" of a soluble oil. TRIM SC9030 is well suited for general high-speed machining and grinding of all materials and it leaves soluble emulsion oil as residue.

  • Compatible with a very wide range of materials including cast iron, steels, copper, aluminum alloys, and many plastics and composites
  • Provides superior corrosion inhibition on cast iron and other ferrous and nonferrous materials; and eliminates the "hot chip" and clinkering problems often seen when machining cast iron
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Has exceptional sump life and very low makeup for extremely low total operating cost
  • Low odor and mist makes for an operator-friendly product
  • Easy recycling or disposal with conventional techniques and equipment

  • TRIM™ TAP HEAVY

    High-lubricity Tapping Fluid

    TRIM TAP HEAVY is a 100% synthetic and vegetable-based lubricant possessing strong friction-reducing properties. Designed as a tough operation product for use with metals of low machinability, it's recommended for use at full-strength, brush-on use for reaming, tapping, and threading.

  • Especially for taps ½" diameter and larger
  • Contains no mineral oils
  • Promotes excellent finish
  • Ensures parts size control
  • Delivers exceptionally long tool life
  • Reduces rubbing of the tool flank
  • Water washable, for easy parts cleaning
  • Compatible with most TRIM fluids
  • Use for added lubricity on extremely tough jobs

  • TRIM™ TAP LIGHT

    Tapping Fluid

    TRIM TAP LIGHT is a synthetic/vegetable/mineral oil blend possessing strong friction-reducing properties. Use with metals of low machinability; specifically recommended at full strength for flooding applications involving broaching, sawing, milling, tapping, threading, gear cutting and shaving, gundrilling, and reaming.

  • Especially for taps ¼" diameter and smaller
  • Promotes excellent finish
  • Ensures parts size control
  • Delivers exceptionally long tool life
  • Reduces rubbing of the tool flank
  • Water washable, for easy parts cleaning
  • Compatible with most TRIM fluids
  • Use for added lubricity on extremely tough jobs

  • TRIM™ TC 108

    Metalworking Fluid Defoamer

    TRIM TC 108 is a highly effective tank side additive used to control foam in metalworking fluid systems.

  • Paintable
  • Plateable

  • TRIM™ TC 109

    Silicone Free, Tank Side Defoamer

    TRIM TC 109 is a silicone free antifoam or defoamer. It is used as a tank-side additive to control foam in water-miscible coolants, washing compounds, floor soaps, etc.

  • Antifoam
  • Silicone free

  • TRIM™ TC 155

    Nonferrous Corrosion Inhibitor

    TRIM TC 155 is a nonferrous corrosion inhibitor for use in water soluble and straight oil systems. It is particularly effective in preventing staining and white rust on die cast alloys containing copper.

  • Prevents staining and white rust on die cast alloys containing copper
  • Nonferrous corrosion inhibition

  • TRIM™ TC 175

    Chlorinated Lubricity Additive

    TRIM TC 175 is a chlorinated EP (extreme pressure) lubrication/emulsifier additive package. It may be added to water-soluble coolant systems to replace or increase the presence of the chlorine EP additives in the system.

  • New, easier to mix formulation
  • New, chlorine EP additives stay in systems longer

  • TRIM™ TC 177

    Odor Mask

    TRIM TC 177 is a "vanilla" odor mask. This product may be used to reduce some of the odors associated with coolant systems.

  • "Vanilla" odor mask

  • TRIM™ TC 241A

    Antifoam

    TRIM TC 241A is a long lasting antifoam that does not contain any of the silicone or poly-siloxane ingredients usually found in antifoam. This unique formula results in much longer functional life when compared to traditional antifoams.

  • Only add to synthetic fluids
  • Use 0.01 (100 PPM) as the add rate
  • Pre-mix in either clean water or coolant working solution
  • Adding a little at a time, “up stream” of the filter helps to ensure maximum effectiveness
  • When properly mixed into the working solution, TRIM TC 241A will pass through filtration down to 2 microns, however, when not properly mixed, it may be filtered out
  • This material is very stable, and when properly mixed, three to four weeks between adds is typical
  • Fluid temperatures must be 21°C or higher at the point of agitation